Tin Ceilings by The Tinman : Chelsea Decorative Metal Company : Tin Ceilings, Pressed Tin, Tin Ceiling Panels, Cornices, Moldings, Custom Ceiling Panels, Embossed Metal Ceilings, Decorative Metal and Backsplashes.
Home Patterns
Styles
Fillers
Cornices Finishes
Installation
Gallery Order
CEILING INSTALLATION INSTRUCTIONS
TOOLS & SUPPLIES:

  • Hammer
  • 1" Common Nails with Head
  • Tin Snips
  • Chalk Line
  • Tape Measure
  • Gloves
  • Note: Caution Should be Used.
    Metal Edges are Very Sharp
INSTRUCTIONS:

1. Using sawhorses and heavy planking, erect scaffolding in the room.

2. To begin, nail furring strips to the ceiling around the perimeter of the room. Distance from the wall depends on size of cornice.
1. Using sawhorses and heavy planking, erect scaffolding in the room. 2. To begin, nail furring strips to the ceiling around the perimeter of the room. Distance from the wall depends on size of cornice. 3. Locate the center of the ceiling, strike a chalk line perpendicular to the ceiling beams. This insures that the furring will be nailed into the beams. Working out from this line, snap chalk lines at 12-inch intervals. Place the edge of the furring strip along each line and areas by inserting shims between the furring strips and the ceiling. If ceiling is level, we find that plywooding the whole ceiling is not only easier but lowers the ceiling less (3/8” or 1/2” is fine).   4. Snap a chalk line on the center of the furring strip in the center of the room. (overlap sheets towards the door, underlap sheets moving away from the door; this is so the seam faces the back.) Align the edge of the sheet with the chalk line and attach the sheet using 1-inch common nail at 6-inch intervals where they overlap and 1-foot intervals down the center. Angle the nails for greater strength and drive them in beside the nipples on the metal sheet; the nipples will be reserved for nailing the seam of the overlapping sheet. The installer should support the metal sheets with furring strip; just to help hold it up while nailing.
3. Locate the center of the ceiling, strike a chalk line perpendicular to the ceiling beams. This insures that the furring will be nailed into the beams. Working out from this line, snap chalk lines at 12-inch intervals. Place the edge of the furring strip along each line and areas by inserting shims between the furring strips and the ceiling. If ceiling is level, we find that plywooding the whole ceiling is not only easier but lowers the ceiling less (3/8” or 1/2” is fine).  

4 & 5. Snap a chalk line on the center of the furring strip in the center of the room. (overlap sheets towards the door, underlap sheets moving away from the door; this is so the seam faces the back.) Align the edge of the sheet with the chalk line and attach the sheet using 1-inch common nail at 6-inch intervals where they overlap and 1-foot intervals down the center. Angle the nails for greater strength and drive them in beside the nipples on the metal sheet; the nipples will be reserved for nailing the seam of the overlapping sheet. The installer should support the metal sheets with furring strip; just to help hold it up while nailing.
5. Snap a chalk line on the center of the furring strip in the center of the room. (overlap sheets towards the door, underlap sheets moving away from the door; this is so the seam faces the back.) Align the edge of the sheet with the chalk line and attach the sheet using 1-inch common nail at 6-inch intervals where they overlap and 1-foot intervals down the center. Angle the nails for greater strength and drive them in beside the nipples on the metal sheet; the nipples will be reserved for nailing the seam of the overlapping sheet. The installer should support the metal sheets with furring strip; just to help hold it up while nailing. 6. Insert cross strips where the sheets overlap to support the seams (not necessary if you installed plywood.) 7. Use metal shears to cut irregular-shaped pieces and holes for light fixtures. 8. Use metal shears to cut irregular-shaped pieces and holes for light fixtures.
6. Insert cross strips where the sheets overlap to support the seams (not necessary if you installed plywood.)

7 & 8. Use metal shears to cut irregular-shaped pieces and holes for light fixtures.

9. Position the trimmed sheets with the cut side next to the wall, where it will be hidden by the cornices.
9. Position the trimmed sheets with the cut side next to the wall, where it will be hidden by the cornices. 10. Seal all seams by tapping with the head of a wide-angled chisel. 11. Nail the cornices to the furring strips at 12-inch intervals along the bottom edge and 6-inch intervals along the top edge. Join the cornices with miter joints, nicking the edges at regular intervals and bending them back to make a tighter seam. Close the seams by tapping with the head of a nail. 12. Paint the finished ceiling with an oil base paint (water-base paint rusts the metal.) “Liquid Solder is a good way to close any gaps when joining the corners with the cornice.
10. Seal all seams by tapping with the head of a wide-angled chisel.

11. Nail the cornices to the furring strips at 12-inch intervals along the bottom edge and 6-inch intervals along the top edge. Join the cornices with miter joints, nicking the edges at regular intervals and bending them back to make a tighter seam. Close the seams by tapping with the head of a nail.

12. Paint the finished ceiling with an oil base paint (water-base paint rusts the metal.) “Liquid Solder is a good way to close any gaps when joining the corners with the cornice.
© 1976 AMERICAN HERITAGE PUBLISHING CO., INC. REPRINTED BY PERMISSION FROM AMERICANA MAGIZINE. JULY-AUGUST 1979. PHOTOGRAPHS BY LARRY COUZENS.
Click here to look for installers in your area.
Chelsea Decorative Metal Co. • 8212 Braewick Drive • Houston, Texas 77074 • Phone 713-721-9200 • Fax 713-776-8661

Tin Ceilings by The Tinman: Chelsea Decorative Metal Company are makers of fine pressed tin ceiling panels, which offer Tin Ceilings, Pressed Tin, Tin Ceiling Panels, Cornices, Moldings, Custom Ceiling Panels, Embossed Metal Ceilings, Decorative Metal and Backsplashes.

Email The Tinman